Fluid Distribution in Heated Tank Jacket Design
- Blog
- Fluid Distribution in Heated Tank Jacket Design
Fluid Distribution in Heated Tank Jacket Design
Table of Contents
- What Is a Tank Jacket?
- Choosing the Heating or Cooling Medium
- Position of Inlet and Outlet Connections
- Channel and Half-Pipe Design
- Flow Velocity and Distribution
- Dead Zones and Air Pockets
- Thermal Expansion
- Pressure Rating and Material
- Temperature Sensors and Control
- Conclusion
In many tanks the product is heated or cooled through a jacket fitted around the outside of the vessel. The fluid circulating inside the jacket transfers heat through the tank wall to or from the product. The more evenly the fluid is distributed within the jacket, the more uniform the temperature inside the tank will be.
What Is a Tank Jacket?
A tank jacket is a second shell around the vessel, or an arrangement of half-pipe channels welded to the outer wall, that forms a heat transfer space. Hot water, steam, thermal oil or a cooling fluid circulating in the jacket gives heat to the product through the wall, or takes heat from it.
The jacket design depends on the size of the tank, the properties of the product and the heating or cooling rate required. Design calculations should be carried out by a qualified engineer.
Choosing the Heating or Cooling Medium
The fluid used in the jacket is selected according to the temperature range required and the plant's utilities. Hot water, steam and thermal oil can be used for heating, while chilled water or a glycol mixture can be used for cooling. Each fluid has different pressure and temperature limits.
The choice should be made together with the process requirements and a safety assessment. For steam jackets, condensate drainage is part of the design.
Position of Inlet and Outlet Connections
The position of the jacket inlet and outlet strongly affects distribution. The connections should be placed so that the fluid spreads across the whole jacket area. A cross-flow arrangement can often give a more even distribution than a single-direction flow.
The position should also suit maintenance and venting. The arrangement must take into account the lowest and highest points of the jacket.
Channel and Half-Pipe Design
In half-pipe jackets, half-pipe sections welded to the tank surface guide the fluid through defined channels. The channel spacing and geometry affect heat transfer efficiency and flow distribution. If the spacing is too wide, the surface between two channels may not heat up adequately.
Channel design should follow the size of the tank and the heating rate required. No fixed channel count or dimension is given here; each project requires its own calculation.
Flow Velocity and Distribution
The flow velocity inside the jacket affects both the heat transfer coefficient and the pressure drop. Very low velocity lets the fluid lose its heat quickly and distribution becomes uneven. Very high velocity increases pressure loss and pump energy.
The flow velocity should be set by design calculation and confirmed with site measurements.
Dead Zones and Air Pockets
Dead zones inside the jacket, where the fluid never reaches, disturb heating uniformity. These zones often occur at channel corners or at points far from the inlet and outlet. Flow analysis can be considered during design to identify them.
Air collecting at the highest points of the jacket can form an air pocket that reduces heat transfer. Vent valves should be used to release air from these points safely.
Thermal Expansion
When a temperature difference develops between the jacket and the tank shell, the materials expand by different amounts. This expansion can create stress at weld seams and on half-pipes. The difference in expansion should be taken into account in the jacket design and sufficient flexibility provided.
The effect of expansion should be calculated for the material and the temperature range. No fixed expansion value is given in this article.
Pressure Rating and Material
The working pressure of the jacket should be defined independently of the tank internal pressure. The pressure of the fluid in the jacket must suit the jacket design pressure. Material selection should be compatible both for the tank shell in contact with the product and for the jacket side.
Pressure limits and material class should be set according to the applicable pressure equipment regulations and standards.
Temperature Sensors and Control
Temperature sensors at the jacket inlet and outlet are used to monitor how effectively the fluid transfers heat. The product temperature inside the tank should be measured by a separate sensor. The control logic can adjust the jacket flow or temperature according to the product temperature.
Sensor placement must account for the delay between the fluid and the product, and for measurement accuracy. This should be reviewed together with the process control engineer.
Conclusion
Fluid distribution in a heated tank jacket improves when the inlet and outlet position, channel design, flow velocity, avoidance of dead zones, thermal expansion and control are considered together. Even distribution supports process quality by keeping the product temperature uniform.
SS Proje provides tank and jacket manufacturing and installation solutions matched to process requirements.

