Static Electricity and Grounding in Powder Transfer Lines

  • Blog
  • Static Electricity and Grounding in Powder Transfer Lines
Static Electricity and Grounding in Powder Transfer Lines
Share

Static Electricity and Grounding in Powder Transfer Lines

Table of Contents

  • How Static Electricity Forms in Powder Transfer
  • Explosion Risk and Minimum Ignition Energy
  • How Grounding Connections Are Made
  • Line Material and Conductivity
  • Hoses and Flexible Connections
  • Air Velocity and Flow Conditions
  • Dust Concentration
  • Measurement and Periodic Inspection
  • Staff Training and Procedures
  • Conclusion

In lines that carry powdered products by pneumatic or mechanical means, electrical charge can build up through friction and separation. If the equipment is not earthed, these charges can become a spark capable of igniting a dust and air mixture. Static control is therefore an essential part of powder transfer design.

How Static Electricity Forms in Powder Transfer

Powder particles gain an electric charge as they rub against the pipe wall and against one another. The effect is stronger in pneumatic conveying at high velocity. Parts made of insulating material can allow charge to build up and to be retained for long periods.

Charge accumulation can be particularly high in non-conductive sections of the line or in equipment that is not earthed. Grounding should therefore cover the whole system, not only the metal parts.

Explosion Risk and Minimum Ignition Energy

Combustible dusts mixed with air within a certain concentration range can form an explosive atmosphere. The minimum energy needed to ignite that atmosphere depends on the type of dust. If a static spark reaches that energy, ignition can occur.

The minimum ignition energy and explosion characteristics of the dust should be taken from the product data sheet or laboratory analysis. These values should not be assumed from a general article like this one.

How Grounding Connections Are Made

Grounding is done by connecting metal equipment and lines to a reliable earth point. Connection points must be clean, free of corrosion and continuous. On painted surfaces, the paint should be removed at the connection point so that bare metal is in contact.

The resistance of the grounding circuit should be measured and continuity verified periodically. The acceptance value should be set according to the applicable standard and the plant regulations.

Line Material and Conductivity

Metal lines are suitable for dissipating charge to earth through their own structure. Insulating parts such as plastic or glass should not be used in the line, or they must be bonded to earth. The conductivity of the line material should be checked at the design stage.

If there are insulating coatings on the internal surface, their effect on charge accumulation should be evaluated separately. Surface smoothness can also influence charge build-up.

Hoses and Flexible Connections

Flexible hoses are used to absorb vibration and movement, but many are made of insulating material. An antistatic, conductive hose should therefore be chosen, with an earthing connection at both ends.

The continuity of hose connections should be checked regularly. When a hose ages or cracks, its conductivity can be lost.

Air Velocity and Flow Conditions

In pneumatic conveying, air velocity directly affects charge generation. A higher velocity means more friction and therefore more charge. The velocity should be kept above the minimum needed for conveying, but should not be raised unnecessarily.

Irregular flow and sudden changes of direction can also cause charge accumulation. Bends and reducers should be designed to keep the flow smooth.

Dust Concentration

The hazard arises when dust concentration reaches the explosive range. It is therefore important to prevent dust from accumulating in the system and to keep airborne dust under control. The cleaning plan should include regular removal of settled dust.

Dust settled on surfaces can also create a secondary ignition risk. Dust accumulation on top of equipment should be checked regularly.

Measurement and Periodic Inspection

Grounding continuity, hose conductivity and equipment connections should be measured at set intervals. The results should be recorded and trends monitored. A connection that loosens or corrodes over time can be an early warning sign.

The inspection period should be set according to the plant's risk assessment and the applicable regulations. A fixed period is not recommended in this article.

Staff Training and Procedures

The effectiveness of grounding depends on how staff apply it. Operators should not begin work before the earthing cable is connected and the connection checked. Training should ensure that the risks and the procedure are understood.

A written work procedure should define the steps to follow during maintenance and when opening the line. All personnel should know and follow this procedure.

Conclusion

Control of static electricity in powder transfer lines comes from understanding how charge forms, making proper grounding connections, using conductive materials and hoses, managing flow conditions and measuring regularly. All of these steps should be applied together to reduce the risk of dust forming an explosive atmosphere.

SS Proje supports the consideration of relevant safety requirements in the design and installation of powder and granular product transfer systems.